Hi everybody
I update the fw module to 1.0beta8, it's ok for that. But i can't find links for the two orther files..
Thanks
Aufgrund derzeit hohem Spamaufkommens werden neue Nutzer sehr restriktiv behandelt. Nach kurzer "Bewährungszeit" hat man als normaler Nutzer weitreichende Rechte und benötigt auch kein Captcha mehr.
.
Nutzer, die sich danach dennoch als Spammer oder Trolle erweisen, können jederzeit wieder auf diesen Status zurückgesetzt oder gebannt werden.
Dasselbe gilt für Versuche, politische Überzeugungen kund zu tun, egal aus welcher Richtung diese kommen.
.
. Achtung! Verwendet bitte für aktuelle Mäher bzw. falls ihr die Firmware eures Mähers kürzlich aktualisiert habt, den aktuellen Release-Candidate der Robonect-Firmware: https://fw.robonect.de/?latest Diese wird in ein paar Tagen als offizielle Firmware verfügbar sein. (Stand: 03.04.2024)
Where is Part 2 and 3 of the Update? [CLEARED]
-
- Forum-Nutzer
- Beiträge: 20
- Registriert: Mi 11. Jan 2017, 18:34
- Wohnort: Cherbourg en France
- Mäher: Husqvarna Automower 105
- Firmware des Mähers (MSW): MSW 6.xx.xx
- Herstellungsjahr: 2016
- Robonect-Modul: Robonect Hx (Rev.4)
- Robonect Firmware: 1.0 beta 7a
Where is Part 2 and 3 of the Update? [CLEARED]
Husqvarna AM105 (Modèle 2016) MSW 6.14.00, SUB-Version 6.01.00
Robonect HX rev 5, firmware 0.9e
Robonect HX rev 5, firmware 0.9e
- shadowkiller
- Forum-Veteran
- Beiträge: 4475
- Registriert: Do 11. Jan 2018, 08:42
- Wohnort: Würzburg
- Mäher: Husqvarna Automower 315
- Firmware des Mähers (MSW): MSW 10.xx.xx
- Herstellungsjahr: 2017 (Modell 2018)
- Robonect-Modul: Robonect Hx (Rev.5)
- Robonect Firmware: 1.3 (WLAN 1.7.4)
- hat sich bedankt: 160 Male
- wurde gedankt: 134 Male
Where is Part 2 and 3 of the Update?
The other files need to become more comfortable for users not accepting/reading/translating the rules standing before the download links....
So Fabian will post them later this days again. You can use Beta 8 either. But you have to wait for some days to get the full bugfixes and features you can get then with Part 2 (ZeroConf) und Part 3 (WiFi) update files.
So Fabian will post them later this days again. You can use Beta 8 either. But you have to wait for some days to get the full bugfixes and features you can get then with Part 2 (ZeroConf) und Part 3 (WiFi) update files.
Anleitung zur Erstinstallation
--
Robonect® Dokumentation (= Gebrauchsanweisung = Bedienungsanleitung) und Support
--
Forum cooler nutzen: Hervorhebungen machen und Screenshots posten
--
Es wurde schon alles gefragt, nur noch nicht von allen. (frei nach Karl Valentin)
--
Robonect® Dokumentation (= Gebrauchsanweisung = Bedienungsanleitung) und Support
--
Forum cooler nutzen: Hervorhebungen machen und Screenshots posten
--
Es wurde schon alles gefragt, nur noch nicht von allen. (frei nach Karl Valentin)
-
- Forum-Nutzer
- Beiträge: 20
- Registriert: Mi 11. Jan 2017, 18:34
- Wohnort: Cherbourg en France
- Mäher: Husqvarna Automower 105
- Firmware des Mähers (MSW): MSW 6.xx.xx
- Herstellungsjahr: 2016
- Robonect-Modul: Robonect Hx (Rev.4)
- Robonect Firmware: 1.0 beta 7a
Re: Where is Part 2 and 3 of the Update?
Yes, sorry for this message
Husqvarna AM105 (Modèle 2016) MSW 6.14.00, SUB-Version 6.01.00
Robonect HX rev 5, firmware 0.9e
Robonect HX rev 5, firmware 0.9e