Aufgrund derzeit hohem Spamaufkommens werden neue Nutzer sehr restriktiv behandelt. Nach kurzer "Bewährungszeit" hat man als normaler Nutzer weitreichende Rechte und benötigt auch kein Captcha mehr.
.
Nutzer, die sich danach dennoch als Spammer oder Trolle erweisen, können jederzeit wieder auf diesen Status zurückgesetzt oder gebannt werden.
Dasselbe gilt für Versuche, politische Überzeugungen kund zu tun, egal aus welcher Richtung diese kommen.
.
. Achtung! Derzeit ist Robonect (noch) nicht mit dem Automower 305 ab Baujahr 2020 zusammen mit der neuen Mäher-FW MSW 41.4.0 kompatibel!
Aber: Im DailyBuild ist ein Patch enthalten, der getestet werden kann! (Stand 15.02.2024)
.
.Du hast Deinen Gardena-Mäher auf die Gardena-Firmware von 2023 aktualisiert?
. Testmöglichkeit für das Daily Build.
Das FW-Update am Mäher wird dennoch nicht empfohlen, da das Daily Build nach aktuellen Berichten von Beta-Testern noch keine vollständige Kompatibilität gewährleisten kann! (Stand: 15.02.2024)
Wir empfehlen, das Gardena-Update noch nicht durchzuführen!
.
.
log coordinates for start
-
- erfahrener Forum-Nutzer
- Beiträge: 67
- Registriert: Di 25. Okt 2016, 18:42
- Wohnort: Denmark
- Mäher: Husqvarna Automower 330X
- Firmware des Mähers (MSW): MSW 7.xx.xx
- Herstellungsjahr: 2014
- Robonect-Modul: Robonect H30x (Rev.3)
- Robonect Firmware: V1.3b
- wurde gedankt: 3 Male
log coordinates for start
It would be interesting to know exaxtly where the mower starts. To keep a tab on how the "find area needing mowing by GPS" is working.,
230acx + 330x
- SenfmitHonig
- sehr erfahrener Forum-Nutzer
- Beiträge: 457
- Registriert: So 30. Okt 2016, 22:39
- Wohnort: 943xx
- Mäher: Husqvarna Automower 430X
- Herstellungsjahr: 2016
- Robonect-Modul: Robonect Hx (Rev.2)
- Robonect Firmware: V1.3
- hat sich bedankt: 4 Male
- wurde gedankt: 34 Male
Re: log coordinates for start
Servus!,
You should be able to see this by the distance the mower moves OUT on the wire tracer....
viewforum.php?f=210
You should be able to see this by the distance the mower moves OUT on the wire tracer....
viewforum.php?f=210
Do you mean something like this?MQTT: -> traveled distance from charging station to starting point
../mower
/distance
-
- erfahrener Forum-Nutzer
- Beiträge: 67
- Registriert: Di 25. Okt 2016, 18:42
- Wohnort: Denmark
- Mäher: Husqvarna Automower 330X
- Firmware des Mähers (MSW): MSW 7.xx.xx
- Herstellungsjahr: 2014
- Robonect-Modul: Robonect H30x (Rev.3)
- Robonect Firmware: V1.3b
- wurde gedankt: 3 Male
Re: log coordinates for start
No, I mean what I say. The lat/long of where the mower went from going OUT to mowing.
Edit: Well, in combination of knowing which wire it searched OUT, it might work, and probably more accurate.
I'll try it when my robonect gets back.
Edit: Well, in combination of knowing which wire it searched OUT, it might work, and probably more accurate.
I'll try it when my robonect gets back.
230acx + 330x
-
- erfahrener Forum-Nutzer
- Beiträge: 67
- Registriert: Di 25. Okt 2016, 18:42
- Wohnort: Denmark
- Mäher: Husqvarna Automower 330X
- Firmware des Mähers (MSW): MSW 7.xx.xx
- Herstellungsjahr: 2014
- Robonect-Modul: Robonect H30x (Rev.3)
- Robonect Firmware: V1.3b
- wurde gedankt: 3 Male
Re: log coordinates for start
I'm getting this from mqtt, I haven't had enough traces yet to see if I can determine which route it traveled.
Here the GPS location is 50 seconds after the mower started. It whould be nice if a Status change triggered a GPS location.
2021-07-15T16:32:44+0200 robonect/mower/Status 5
2021-07-15T16:32:44+0200 robonect/mower/Status/plain Searching
2021-07-15T16:32:44+0200 robonect/mower/substatus 0
2021-07-15T16:32:44+0200 robonect/mower/substatus/plain
2021-07-15T16:32:44+0200 robonect/mower/Status/duration 0 Min.
2021-07-15T16:32:45+0200 robonect/mower/Status/plain Searching (65m)
2021-07-15T16:32:45+0200 robonect/mower/distance 65 m
2021-07-15T16:32:45+0200 robonect/mower/Status/plain Searching
2021-07-15T16:32:45+0200 robonect/mower/distance 0 m
2021-07-15T16:32:45+0200 robonect/mower/substatus 15
2021-07-15T16:32:45+0200 robonect/mower/substatus/plain Exit angle
2021-07-15T16:32:52+0200 robonect/mower/Status 2
2021-07-15T16:32:52+0200 robonect/mower/Status/plain Mowing
2021-07-15T16:32:52+0200 robonect/mower/substatus 1
2021-07-15T16:32:52+0200 robonect/mower/substatus/plain drives
2021-07-15T16:32:52+0200 robonect/mower/mode 1
2021-07-15T16:32:53+0200 robonect/mower/battery/charge 99 %
2021-07-15T16:33:42+0200 robonect/GPS/satellites 14
2021-07-15T16:33:42+0200 robonect/GPS/latitude xx°19.4559 N
2021-07-15T16:33:42+0200 robonect/GPS/longitude yy°28.7423 E
Here the GPS location is 50 seconds after the mower started. It whould be nice if a Status change triggered a GPS location.
2021-07-15T16:32:44+0200 robonect/mower/Status 5
2021-07-15T16:32:44+0200 robonect/mower/Status/plain Searching
2021-07-15T16:32:44+0200 robonect/mower/substatus 0
2021-07-15T16:32:44+0200 robonect/mower/substatus/plain
2021-07-15T16:32:44+0200 robonect/mower/Status/duration 0 Min.
2021-07-15T16:32:45+0200 robonect/mower/Status/plain Searching (65m)
2021-07-15T16:32:45+0200 robonect/mower/distance 65 m
2021-07-15T16:32:45+0200 robonect/mower/Status/plain Searching
2021-07-15T16:32:45+0200 robonect/mower/distance 0 m
2021-07-15T16:32:45+0200 robonect/mower/substatus 15
2021-07-15T16:32:45+0200 robonect/mower/substatus/plain Exit angle
2021-07-15T16:32:52+0200 robonect/mower/Status 2
2021-07-15T16:32:52+0200 robonect/mower/Status/plain Mowing
2021-07-15T16:32:52+0200 robonect/mower/substatus 1
2021-07-15T16:32:52+0200 robonect/mower/substatus/plain drives
2021-07-15T16:32:52+0200 robonect/mower/mode 1
2021-07-15T16:32:53+0200 robonect/mower/battery/charge 99 %
2021-07-15T16:33:42+0200 robonect/GPS/satellites 14
2021-07-15T16:33:42+0200 robonect/GPS/latitude xx°19.4559 N
2021-07-15T16:33:42+0200 robonect/GPS/longitude yy°28.7423 E
230acx + 330x