I'm having Timer issues with the new firmware.
First problem is getting access to them in the Robonect web UI.
I'd click Timer 1, and get a blank page. If I go down the list clicking Timer 2,3,4,5 etc until I get one to show, I can then again click Timer 1 and get it to show. This is one example.
The second Timer issue is that yesterday, I changed Timer 1 settings, and deactivated Timer 2. None of these settings were saved to the mower, but looked fine in Robonect web UI. After a reboot of the machine, Robonect web UI showed the old Timer settings. Changing them again, via Robonect web UI seems to have worked, using the "click until I get a Timer to show" method described in the first paragraph.
Timer issues [CLARIFIED]
-
- sehr erfahrener Forum-Nutzer
- Beiträge: 120
- Registriert: So 26. Mär 2017, 11:31
- Wohnort: Sweden
- Mäher: Gardena smart SILENO
- Robonect-Modul: Robonect Hx (Rev.5)
- Robonect Firmware: 1.4
- hat sich bedankt: 6 Male
- wurde gedankt: 20 Male
- Kontaktdaten:
Timer issues [CLARIFIED]
Zuletzt geändert von shadowkiller am Fr 5. Jun 2020, 19:35, insgesamt 1-mal geändert.
Grund: Title customized
Grund: Title customized
Best regards,
David from Sweden
David from Sweden
- shadowkiller
- Forum-Veteran
- Beiträge: 4475
- Registriert: Do 11. Jan 2018, 08:42
- Wohnort: Würzburg
- Mäher: Husqvarna Automower 315
- Firmware des Mähers (MSW): MSW 10.xx.xx
- Herstellungsjahr: 2017 (Modell 2018)
- Robonect-Modul: Robonect Hx (Rev.5)
- Robonect Firmware: 1.3 (WLAN 1.7.4)
- hat sich bedankt: 160 Male
- wurde gedankt: 135 Male
Re: Timer issues
Anleitung zur Erstinstallation
--
Robonect® Dokumentation (= Gebrauchsanweisung = Bedienungsanleitung) und Support
--
Forum cooler nutzen: Hervorhebungen machen und Screenshots posten
--
Es wurde schon alles gefragt, nur noch nicht von allen. (frei nach Karl Valentin)
--
Robonect® Dokumentation (= Gebrauchsanweisung = Bedienungsanleitung) und Support
--
Forum cooler nutzen: Hervorhebungen machen und Screenshots posten
--
Es wurde schon alles gefragt, nur noch nicht von allen. (frei nach Karl Valentin)
-
- sehr erfahrener Forum-Nutzer
- Beiträge: 120
- Registriert: So 26. Mär 2017, 11:31
- Wohnort: Sweden
- Mäher: Gardena smart SILENO
- Robonect-Modul: Robonect Hx (Rev.5)
- Robonect Firmware: 1.4
- hat sich bedankt: 6 Male
- wurde gedankt: 20 Male
- Kontaktdaten:
Re: Timer issues [CLARIFIED]
Ok, that clarified a few things, but not the whole thing.
1. I've not created or changed a Timer on the mower itself, since I installed my Robonect in 2017 or 2018.
2. I'm having issues getting the web UI to actually show them (It's giving me a white blank page).
I hade none of these issues in 1.1b or earlier.
1. I've not created or changed a Timer on the mower itself, since I installed my Robonect in 2017 or 2018.
2. I'm having issues getting the web UI to actually show them (It's giving me a white blank page).
I hade none of these issues in 1.1b or earlier.
Best regards,
David from Sweden
David from Sweden
- shadowkiller
- Forum-Veteran
- Beiträge: 4475
- Registriert: Do 11. Jan 2018, 08:42
- Wohnort: Würzburg
- Mäher: Husqvarna Automower 315
- Firmware des Mähers (MSW): MSW 10.xx.xx
- Herstellungsjahr: 2017 (Modell 2018)
- Robonect-Modul: Robonect Hx (Rev.5)
- Robonect Firmware: 1.3 (WLAN 1.7.4)
- hat sich bedankt: 160 Male
- wurde gedankt: 135 Male
Re: Timer issues [CLARIFIED]
Please try to use Beta-FW 1.2 (RC0) (Beta-Forum)
Anleitung zur Erstinstallation
--
Robonect® Dokumentation (= Gebrauchsanweisung = Bedienungsanleitung) und Support
--
Forum cooler nutzen: Hervorhebungen machen und Screenshots posten
--
Es wurde schon alles gefragt, nur noch nicht von allen. (frei nach Karl Valentin)
--
Robonect® Dokumentation (= Gebrauchsanweisung = Bedienungsanleitung) und Support
--
Forum cooler nutzen: Hervorhebungen machen und Screenshots posten
--
Es wurde schon alles gefragt, nur noch nicht von allen. (frei nach Karl Valentin)
-
- sehr erfahrener Forum-Nutzer
- Beiträge: 120
- Registriert: So 26. Mär 2017, 11:31
- Wohnort: Sweden
- Mäher: Gardena smart SILENO
- Robonect-Modul: Robonect Hx (Rev.5)
- Robonect Firmware: 1.4
- hat sich bedankt: 6 Male
- wurde gedankt: 20 Male
- Kontaktdaten:
Re: Timer issues [CLARIFIED]
That's what I'm using, and you moved my thread from the "bugs" subforumshadowkiller hat geschrieben: ↑Mo 8. Jun 2020, 18:36 Please try to use Beta-FW 1.2 (RC0) (Beta-Forum)
Best regards,
David from Sweden
David from Sweden
- shadowkiller
- Forum-Veteran
- Beiträge: 4475
- Registriert: Do 11. Jan 2018, 08:42
- Wohnort: Würzburg
- Mäher: Husqvarna Automower 315
- Firmware des Mähers (MSW): MSW 10.xx.xx
- Herstellungsjahr: 2017 (Modell 2018)
- Robonect-Modul: Robonect Hx (Rev.5)
- Robonect Firmware: 1.3 (WLAN 1.7.4)
- hat sich bedankt: 160 Male
- wurde gedankt: 135 Male
Re: Timer issues [CLARIFIED]
Ok. But which problems are left?
Anleitung zur Erstinstallation
--
Robonect® Dokumentation (= Gebrauchsanweisung = Bedienungsanleitung) und Support
--
Forum cooler nutzen: Hervorhebungen machen und Screenshots posten
--
Es wurde schon alles gefragt, nur noch nicht von allen. (frei nach Karl Valentin)
--
Robonect® Dokumentation (= Gebrauchsanweisung = Bedienungsanleitung) und Support
--
Forum cooler nutzen: Hervorhebungen machen und Screenshots posten
--
Es wurde schon alles gefragt, nur noch nicht von allen. (frei nach Karl Valentin)