I just got my Robonect installed two days ago. I connected to the wifi, upgraded the firmware, connected it to my own wifi, and was able to see and control the mower from the web. So far so good!
I've had an error since day on that says "This firmware is not supported, please request a new one", but I see I'm not alone with that error.
Last night I was looking in the web interface, so I did a little maintenance, like disabling the mowers own access-point (there should be no reason to have it on after setup). And it still was working fine a couple of hours after that.
Then suddenly it stopped. I can't connect to it's static ip (I set it to 192.168.0.43 during the initial setup), and the SSID I disabled earlier is showing again ("Mein Robomower" or whatever it is). I can connect to the mowers network, but can't reach the webserver and I don't get an IP from the mowers DHCP server.
This is not looking so good....
Is there any way to get this up and running again without disassembling the mower?
How can I prevent this error in the future?
... and what exactly went wrong?
Lost wifi connectivity
- saugbaer
- Forum-Veteran
- Beiträge: 1392
- Registriert: Mo 18. Apr 2016, 01:30
- Wohnort: Ramelsloh
- Mäher: Husqvarna Automower 310
- Firmware des Mähers (MSW): MSW 7.xx.xx
- Herstellungsjahr: 2022
- Robonect-Modul: Robonect Hx (Rev.5)
- Robonect Firmware: V1.4 beta 08.04.2023 20:42
- hat sich bedankt: 7 Male
- wurde gedankt: 10 Male
Re: Lost wifi connectivity
These solutions could help
1. reset PIN
. 2. Set the time to manual
3. shutdown delay
. sorry for my englisch
1. reset PIN
. 2. Set the time to manual
3. shutdown delay
. sorry for my englisch
Ich bin nicht die Signatur, ich putz hier nur
AVM 7490 Fw.7.57 + 2AP's (FRITZ!Powerline 546E + FRITZ!WLAN Repeater 1160 Fw.7.15) HX + APP + VPN + Kamera + LED
AVM 7490 Fw.7.57 + 2AP's (FRITZ!Powerline 546E + FRITZ!WLAN Repeater 1160 Fw.7.15) HX + APP + VPN + Kamera + LED
- Moskus
- Forum-Anfänger
- Beiträge: 7
- Registriert: Do 29. Jun 2017, 08:58
- Wohnort: Norway
- Mäher: Gardena R40Li
- Firmware des Mähers (MSW): MSW 2.xx.xx
- Herstellungsjahr: 2011
- Robonect-Modul: Robonect Hx (Rev.4)
- Robonect Firmware: 0.9e
- hat sich bedankt: 1 Mal
- Kontaktdaten:
Re: Lost wifi connectivity
Thank you! I'll try this when I get home!
It's not worse than mine.
It's the worlds most common language: "Bad english".
- saugbaer
- Forum-Veteran
- Beiträge: 1392
- Registriert: Mo 18. Apr 2016, 01:30
- Wohnort: Ramelsloh
- Mäher: Husqvarna Automower 310
- Firmware des Mähers (MSW): MSW 7.xx.xx
- Herstellungsjahr: 2022
- Robonect-Modul: Robonect Hx (Rev.5)
- Robonect Firmware: V1.4 beta 08.04.2023 20:42
- hat sich bedankt: 7 Male
- wurde gedankt: 10 Male
Re: Lost wifi connectivity
BIGTHX "Google Translater"
Ich bin nicht die Signatur, ich putz hier nur
AVM 7490 Fw.7.57 + 2AP's (FRITZ!Powerline 546E + FRITZ!WLAN Repeater 1160 Fw.7.15) HX + APP + VPN + Kamera + LED
AVM 7490 Fw.7.57 + 2AP's (FRITZ!Powerline 546E + FRITZ!WLAN Repeater 1160 Fw.7.15) HX + APP + VPN + Kamera + LED
- Moskus
- Forum-Anfänger
- Beiträge: 7
- Registriert: Do 29. Jun 2017, 08:58
- Wohnort: Norway
- Mäher: Gardena R40Li
- Firmware des Mähers (MSW): MSW 2.xx.xx
- Herstellungsjahr: 2011
- Robonect-Modul: Robonect Hx (Rev.4)
- Robonect Firmware: 0.9e
- hat sich bedankt: 1 Mal
- Kontaktdaten:
Re: Lost wifi connectivity
Using the Reset Pin worked! It just took me a while to figure out that you are supposed to subtract your own pin from 9999 and use the result as the Reset Pin.
All is well again, and its good to know that I don't necessary have to pick the mower apart just to hit a reset button...
All is well again, and its good to know that I don't necessary have to pick the mower apart just to hit a reset button...