I have been running robonect for around two years, with constantly recurring network issues.
In the beginning I thought it was simply my wifi, but now everything has been replaced and the issues still appear constantly. Even when in the charging station next to the house.
- An wemos d1 esp in same position has no problems communicating with wifi.
- Distance to unifi wifi station is approximately 5m.
- When I manage to login, robonect reports wifi quality ~-77-78dBm wich sounds reasonable.
Problems:
- When trying to access Robonect, I can usually reach http auth, but it fails to continue. (Same problem when actings as wifi client or robonect's own wifi network).
- Curl on the ip shows ~60% fail to even recieve the http auth headers.
- Pinging on the ip is randomly between 2mS -> 200mS -> timeout.
- mqtt sometimes send a lot of offline messages.
Sometimes, a power cycling of the robot makes the web ui respond. Sometimes nothing works.
Firmware is now updated to V1.0 Beta 7a, same problem still appears. This has always been the case with this module. (On first startup it was there, I send a lot of mails to admin about getting it running the first time).
Aufgrund derzeit hohem Spamaufkommens werden neue Nutzer sehr restriktiv behandelt. Nach kurzer "Bewährungszeit" hat man als normaler Nutzer weitreichende Rechte und benötigt auch kein Captcha mehr.
.
Nutzer, die sich danach dennoch als Spammer oder Trolle erweisen, können jederzeit wieder auf diesen Status zurückgesetzt oder gebannt werden.
Dasselbe gilt für Versuche, politische Überzeugungen kund zu tun, egal aus welcher Richtung diese kommen.
.
. Achtung! Derzeit ist Robonect (noch) nicht mit dem Automower 305 ab Baujahr 2020 zusammen mit der neuen Mäher-FW MSW 41.4.0 kompatibel!
Aber: Im DailyBuild ist ein Patch enthalten, der getestet werden kann! (Stand 15.02.2024)
.
.Du hast Deinen Gardena-Mäher auf die Gardena-Firmware von 2023 aktualisiert?
. Testmöglichkeit für das Daily Build.
Das FW-Update am Mäher wird dennoch nicht empfohlen, da das Daily Build nach aktuellen Berichten von Beta-Testern noch keine vollständige Kompatibilität gewährleisten kann! (Stand: 15.02.2024)
Wir empfehlen, das Gardena-Update noch nicht durchzuführen!
.
.
Problem accessing robonect on R70Li [GELÖST IN BETA8]
-
- Forum-Nutzer
- Beiträge: 18
- Registriert: Do 25. Mai 2017, 11:49
- Wohnort: Vasa, Finland
- Mäher: Gardena R70Li
- Firmware des Mähers (MSW): MSW 5.xx.xx
- Herstellungsjahr: 2014
- Robonect-Modul: Robonect Hx (Rev.4)
- Robonect Firmware: 1.0b7
Problem accessing robonect on R70Li [GELÖST IN BETA8]
Zuletzt geändert von shadowkiller am So 23. Jun 2019, 13:40, insgesamt 1-mal geändert.
Grund: Titel an aktuellen Status angepasst
Grund: Titel an aktuellen Status angepasst
-
- Forum-Nutzer
- Beiträge: 18
- Registriert: Do 25. Mai 2017, 11:49
- Wohnort: Vasa, Finland
- Mäher: Gardena R70Li
- Firmware des Mähers (MSW): MSW 5.xx.xx
- Herstellungsjahr: 2014
- Robonect-Modul: Robonect Hx (Rev.4)
- Robonect Firmware: 1.0b7
Re: Problem accessing robonect on R70Li
Some ideas to fix this:
- I have performed a factory reset.
- I setup a separate wifi which is only 2.4GHz to avoid potential problems.
- Disabled internal access point once connected to new network.
Hopefully this solves the problem now.
- I have performed a factory reset.
- I setup a separate wifi which is only 2.4GHz to avoid potential problems.
- Disabled internal access point once connected to new network.
Hopefully this solves the problem now.
-
- Forum-Nutzer
- Beiträge: 18
- Registriert: Do 25. Mai 2017, 11:49
- Wohnort: Vasa, Finland
- Mäher: Gardena R70Li
- Firmware des Mähers (MSW): MSW 5.xx.xx
- Herstellungsjahr: 2014
- Robonect-Modul: Robonect Hx (Rev.4)
- Robonect Firmware: 1.0b7
Re: Problem accessing robonect on R70Li
Same issue still. UI keeps getting stuck. It might even load half a page, so a word is loaded only half, buttons in end of page are missing, etc. Reloading eventually might work.
I tried downloading the logbook but it says:
Attached Screenshot of firmware information.
I tried downloading the logbook but it says:
Code: Alles auswählen
<successful>false</successful>
<error_code>253</error_code>
<error_message>Logbook damaged! (6)</error_message>
- saugbaer
- Forum-Veteran
- Beiträge: 1392
- Registriert: Mo 18. Apr 2016, 01:30
- Wohnort: Ramelsloh
- Mäher: Husqvarna Automower 310
- Firmware des Mähers (MSW): MSW 7.xx.xx
- Herstellungsjahr: 2022
- Robonect-Modul: Robonect Hx (Rev.5)
- Robonect Firmware: V1.3b (14.06.2022)
- hat sich bedankt: 7 Male
- wurde gedankt: 10 Male
Re: Problem accessing robonect on R70Li
write Fabian (Admin) a PN
(He has developed a new WLAN driver)
bootloader is old
Wi-Fi is old
.
(He has developed a new WLAN driver)
bootloader is old
Wi-Fi is old
.
Ich bin nicht die Signatur, ich putz hier nur
AVM 7490 Fw.7.57 + 2AP's (FRITZ!Powerline 546E + FRITZ!WLAN Repeater 1160 Fw.7.15) HX + APP + VPN + Kamera + LED
AVM 7490 Fw.7.57 + 2AP's (FRITZ!Powerline 546E + FRITZ!WLAN Repeater 1160 Fw.7.15) HX + APP + VPN + Kamera + LED
-
- Forum-Nutzer
- Beiträge: 18
- Registriert: Do 25. Mai 2017, 11:49
- Wohnort: Vasa, Finland
- Mäher: Gardena R70Li
- Firmware des Mähers (MSW): MSW 5.xx.xx
- Herstellungsjahr: 2014
- Robonect-Modul: Robonect Hx (Rev.4)
- Robonect Firmware: 1.0b7
Re: Problem accessing robonect on R70Li
Upgraded firmware. Seems a bit more stable but still get intermediate timeouts. I'll run this for a while and report back.
-
- Forum-Nutzer
- Beiträge: 18
- Registriert: Do 25. Mai 2017, 11:49
- Wohnort: Vasa, Finland
- Mäher: Gardena R70Li
- Firmware des Mähers (MSW): MSW 5.xx.xx
- Herstellungsjahr: 2014
- Robonect-Modul: Robonect Hx (Rev.4)
- Robonect Firmware: 1.0b7
Re: Problem accessing robonect on R70Li
A few days later. It's not perfect, but it's at least 150 times better. Very nice improvement! Thanks @admin and @saugbaer.