Wenn Sie Push-URL verwenden, ist dies in der Regel für Heimautomatisierungssysteme. Leider ist die Feld-URL viel zu kurz. Meistens ist die URL lang, weil sie einen API KEY und einige IDS enthält
Apropos. Wenn die Push-URL durch Trigger konfiguriert werden kann, z. B. in den Schlafmodus. WARUM ist das Zeitintervall obligatorisch? Könnten wir das Zeitintervall nicht einfach deaktivieren, wenn wir nur Trigger verwenden wollen?
Gibt es einen Weg ?
---------------------
When using push url it's generaly for home automation system. Unfortunately the field url is way too short. Most of the time the url is long because it contains an APIKEY and some IDS
By the way. If the push url can be configured by triggers such as entering sleep mode for example. WHy the time interval is mandatory ? Couldn't we just desactivate the time interval if we only want to use triggers ?
IS there a way ?
URL drücken frage
- shadowkiller
- Forum-Veteran
- Beiträge: 4475
- Registriert: Do 11. Jan 2018, 08:42
- Wohnort: Würzburg
- Mäher: Husqvarna Automower 315
- Firmware des Mähers (MSW): MSW 10.xx.xx
- Herstellungsjahr: 2017 (Modell 2018)
- Robonect-Modul: Robonect Hx (Rev.5)
- Robonect Firmware: 1.3 (WLAN 1.7.4)
- hat sich bedankt: 160 Male
- wurde gedankt: 135 Male
Re: URL drücken frage
Is this a bug report or a feature request?
shadowkiller
shadowkiller
Anleitung zur Erstinstallation
--
Robonect® Dokumentation (= Gebrauchsanweisung = Bedienungsanleitung) und Support
--
Forum cooler nutzen: Hervorhebungen machen und Screenshots posten
--
Es wurde schon alles gefragt, nur noch nicht von allen. (frei nach Karl Valentin)
--
Robonect® Dokumentation (= Gebrauchsanweisung = Bedienungsanleitung) und Support
--
Forum cooler nutzen: Hervorhebungen machen und Screenshots posten
--
Es wurde schon alles gefragt, nur noch nicht von allen. (frei nach Karl Valentin)
-
- Forum-Nutzer
- Beiträge: 20
- Registriert: Mi 25. Apr 2018, 13:59
- Mäher: Husqvarna Automower 315
- Firmware des Mähers (MSW): MSW 6.xx.xx
- Herstellungsjahr: 2017
- Robonect-Modul: Robonect Hx (Rev.5)
- Robonect Firmware: 1.0beta7
Re: URL drücken frage
You are right ! Didn't notice the feature request section !!
But maybe the size limitation can be considered as a bug , i don't really know if the size limitation is wanted.
But you are totally right for the time interval option. Sorry
But maybe the size limitation can be considered as a bug , i don't really know if the size limitation is wanted.
But you are totally right for the time interval option. Sorry
- shadowkiller
- Forum-Veteran
- Beiträge: 4475
- Registriert: Do 11. Jan 2018, 08:42
- Wohnort: Würzburg
- Mäher: Husqvarna Automower 315
- Firmware des Mähers (MSW): MSW 10.xx.xx
- Herstellungsjahr: 2017 (Modell 2018)
- Robonect-Modul: Robonect Hx (Rev.5)
- Robonect Firmware: 1.3 (WLAN 1.7.4)
- hat sich bedankt: 160 Male
- wurde gedankt: 135 Male
Re: URL drücken frage
Thanks for answering
shadowkiller
shadowkiller
Anleitung zur Erstinstallation
--
Robonect® Dokumentation (= Gebrauchsanweisung = Bedienungsanleitung) und Support
--
Forum cooler nutzen: Hervorhebungen machen und Screenshots posten
--
Es wurde schon alles gefragt, nur noch nicht von allen. (frei nach Karl Valentin)
--
Robonect® Dokumentation (= Gebrauchsanweisung = Bedienungsanleitung) und Support
--
Forum cooler nutzen: Hervorhebungen machen und Screenshots posten
--
Es wurde schon alles gefragt, nur noch nicht von allen. (frei nach Karl Valentin)