Cannot access robonect after a couple of days [TRY TO USE V1.6.2]
-
- Forum-Nutzer
- Beiträge: 23
- Registriert: Di 30. Apr 2019, 13:36
- Wohnort: Sweden
- Mäher: McCulloch ROB R1000
- Firmware des Mähers (MSW): MSW 6.xx.xx
- Robonect-Modul: Robonect Hx (Rev.5)
- Robonect Firmware: 1.1b
Cannot access robonect after a couple of days [TRY TO USE V1.6.2]
Went fine for me as well and have been mowing for a couple of days. But now I cannot connect any more. It keeps mowing and the router has it connected (even after a power cycle) but I cannot access the web interface. With the robonect app I can get a glimpse of connection (it uses the API?) sometimes but it keeps losing it. What can i try?
- shadowkiller
- Forum-Veteran
- Beiträge: 4475
- Registriert: Do 11. Jan 2018, 08:42
- Wohnort: Würzburg
- Mäher: Husqvarna Automower 315
- Firmware des Mähers (MSW): MSW 10.xx.xx
- Herstellungsjahr: 2017 (Modell 2018)
- Robonect-Modul: Robonect Hx (Rev.5)
- Robonect Firmware: 1.3 (WLAN 1.7.4)
- hat sich bedankt: 160 Male
- wurde gedankt: 135 Male
Re: Cannot access robonect after firmware install
Hey,
You can
try to use some other devices to connect the local IP of Robonect in your home WiFi
try to use another browser.
try to delete browser cache and cookies of robonect and then to reconnect.
try to change the channel of your AP connecting to Robonect.
try to connect the AP of Robonect if not switched off.
try to make a PIN-Reset (please read the hint for this, the link is in my footer)
try to make a Hardware-Reset (please read the hint for this)
This all in escalating order and please tell us which one did help
You can
try to use some other devices to connect the local IP of Robonect in your home WiFi
try to use another browser.
try to delete browser cache and cookies of robonect and then to reconnect.
try to change the channel of your AP connecting to Robonect.
try to connect the AP of Robonect if not switched off.
try to make a PIN-Reset (please read the hint for this, the link is in my footer)
try to make a Hardware-Reset (please read the hint for this)
This all in escalating order and please tell us which one did help
Anleitung zur Erstinstallation
--
Robonect® Dokumentation (= Gebrauchsanweisung = Bedienungsanleitung) und Support
--
Forum cooler nutzen: Hervorhebungen machen und Screenshots posten
--
Es wurde schon alles gefragt, nur noch nicht von allen. (frei nach Karl Valentin)
--
Robonect® Dokumentation (= Gebrauchsanweisung = Bedienungsanleitung) und Support
--
Forum cooler nutzen: Hervorhebungen machen und Screenshots posten
--
Es wurde schon alles gefragt, nur noch nicht von allen. (frei nach Karl Valentin)
-
- Forum-Nutzer
- Beiträge: 20
- Registriert: Mi 11. Jan 2017, 18:34
- Wohnort: Cherbourg en France
- Mäher: Husqvarna Automower 105
- Firmware des Mähers (MSW): MSW 6.xx.xx
- Herstellungsjahr: 2016
- Robonect-Modul: Robonect Hx (Rev.4)
- Robonect Firmware: 1.0 beta 7a
Re: Cannot access robonect after firmware install
Hi
I add this bug before update 1.7 wlan driver. The simple way to reconnect to lower is to disable and enable wlan on the router.
I add this bug before update 1.7 wlan driver. The simple way to reconnect to lower is to disable and enable wlan on the router.
Husqvarna AM105 (Modèle 2016) MSW 6.14.00, SUB-Version 6.01.00
Robonect HX rev 5, firmware 0.9e
Robonect HX rev 5, firmware 0.9e
- shadowkiller
- Forum-Veteran
- Beiträge: 4475
- Registriert: Do 11. Jan 2018, 08:42
- Wohnort: Würzburg
- Mäher: Husqvarna Automower 315
- Firmware des Mähers (MSW): MSW 10.xx.xx
- Herstellungsjahr: 2017 (Modell 2018)
- Robonect-Modul: Robonect Hx (Rev.5)
- Robonect Firmware: 1.3 (WLAN 1.7.4)
- hat sich bedankt: 160 Male
- wurde gedankt: 135 Male
Re: Cannot access robonect after firmware install
You can also try the other release date version of the 1.7 WLAN driver ...
EDIT: You can try to downgrade to Driver version 1.6.2, too.
Any of this driver versions may solve your problem. Please report!
EDIT: You can try to downgrade to Driver version 1.6.2, too.
Any of this driver versions may solve your problem. Please report!
Anleitung zur Erstinstallation
--
Robonect® Dokumentation (= Gebrauchsanweisung = Bedienungsanleitung) und Support
--
Forum cooler nutzen: Hervorhebungen machen und Screenshots posten
--
Es wurde schon alles gefragt, nur noch nicht von allen. (frei nach Karl Valentin)
--
Robonect® Dokumentation (= Gebrauchsanweisung = Bedienungsanleitung) und Support
--
Forum cooler nutzen: Hervorhebungen machen und Screenshots posten
--
Es wurde schon alles gefragt, nur noch nicht von allen. (frei nach Karl Valentin)
-
- Forum-Nutzer
- Beiträge: 23
- Registriert: Di 30. Apr 2019, 13:36
- Wohnort: Sweden
- Mäher: McCulloch ROB R1000
- Firmware des Mähers (MSW): MSW 6.xx.xx
- Robonect-Modul: Robonect Hx (Rev.5)
- Robonect Firmware: 1.1b
Re: Cannot access robonect after a couple of days [WAITING FOR USER]
Got it to work by moving the mower really close to the router antenna. I have the "earlier" of the wlan 1.7 drivers but it seems that it is less powerful than 1.6.2 (I think) that I had earlier.
I can send the logbook if you want. It is downloading now but the speed is about 2kbps (maybe a driver problem?)
I can send the logbook if you want. It is downloading now but the speed is about 2kbps (maybe a driver problem?)
- shadowkiller
- Forum-Veteran
- Beiträge: 4475
- Registriert: Do 11. Jan 2018, 08:42
- Wohnort: Würzburg
- Mäher: Husqvarna Automower 315
- Firmware des Mähers (MSW): MSW 10.xx.xx
- Herstellungsjahr: 2017 (Modell 2018)
- Robonect-Modul: Robonect Hx (Rev.5)
- Robonect Firmware: 1.3 (WLAN 1.7.4)
- hat sich bedankt: 160 Male
- wurde gedankt: 135 Male
Re: Cannot access robonect after a couple of days [TRY TO USE V1.6.2]
You can try out V1.6.2 and go back to 1.7, if you want to test.
Anleitung zur Erstinstallation
--
Robonect® Dokumentation (= Gebrauchsanweisung = Bedienungsanleitung) und Support
--
Forum cooler nutzen: Hervorhebungen machen und Screenshots posten
--
Es wurde schon alles gefragt, nur noch nicht von allen. (frei nach Karl Valentin)
--
Robonect® Dokumentation (= Gebrauchsanweisung = Bedienungsanleitung) und Support
--
Forum cooler nutzen: Hervorhebungen machen und Screenshots posten
--
Es wurde schon alles gefragt, nur noch nicht von allen. (frei nach Karl Valentin)