Hi,
Back from business trip last night, i was forced to install firmware V1.0a on my ROB1000.
Everything was fine with V1.0 but now, my robot doesn't respect the Timer settings and mows all the time in Auto mode
It's scary because my robot can be damaged with the sprinklers working.
Can you please have a look at it ?
Aufgrund derzeit hohem Spamaufkommens werden neue Nutzer sehr restriktiv behandelt. Nach kurzer "Bewährungszeit" hat man als normaler Nutzer weitreichende Rechte und benötigt auch kein Captcha mehr.
.
Nutzer, die sich danach dennoch als Spammer oder Trolle erweisen, können jederzeit wieder auf diesen Status zurückgesetzt oder gebannt werden.
Dasselbe gilt für Versuche, politische Überzeugungen kund zu tun, egal aus welcher Richtung diese kommen.
.
. Achtung! Verwendet bitte für aktuelle Mäher bzw. falls ihr die Firmware eures Mähers kürzlich aktualisiert habt, den aktuellen Release-Candidate der Robonect-Firmware: https://fw.robonect.de/?latest Diese wird in ein paar Tagen als offizielle Firmware verfügbar sein. (Stand: 03.04.2024)
[Solved] [V1.0a] Does not respect timer settings
-
- Forum-Nutzer
- Beiträge: 32
- Registriert: Di 11. Sep 2018, 11:39
- Wohnort: France
- Mäher: McCulloch ROB R1000
- Firmware des Mähers (MSW): MSW 6.xx.xx
- Herstellungsjahr: 2017
- Robonect-Modul: Robonect Hx (Rev.5)
- Robonect Firmware: V1.1b ROB 1000 test
Re: [Solved] [V1.0a] Does not respect timer settings
Finally solve.
I switched off manually the robot through the power button.
Once On again, i saw an unknown Timer activated in Robonect.
I deactivated it and reactivated the other ones.
I notice, one of my active Timer had an old value.
It's like this last firmware update activated very old timers.
Never happened before.
But problem solved
I switched off manually the robot through the power button.
Once On again, i saw an unknown Timer activated in Robonect.
I deactivated it and reactivated the other ones.
I notice, one of my active Timer had an old value.
It's like this last firmware update activated very old timers.
Never happened before.
But problem solved
- shadowkiller
- Forum-Veteran
- Beiträge: 4475
- Registriert: Do 11. Jan 2018, 08:42
- Wohnort: Würzburg
- Mäher: Husqvarna Automower 315
- Firmware des Mähers (MSW): MSW 10.xx.xx
- Herstellungsjahr: 2017 (Modell 2018)
- Robonect-Modul: Robonect Hx (Rev.5)
- Robonect Firmware: 1.3 (WLAN 1.7.4)
- hat sich bedankt: 160 Male
- wurde gedankt: 135 Male
Re: [Solved] [V1.0a] Does not respect timer settings
Thanks for your report. Maybe you can help others which have the same issue.
Anleitung zur Erstinstallation
--
Robonect® Dokumentation (= Gebrauchsanweisung = Bedienungsanleitung) und Support
--
Forum cooler nutzen: Hervorhebungen machen und Screenshots posten
--
Es wurde schon alles gefragt, nur noch nicht von allen. (frei nach Karl Valentin)
--
Robonect® Dokumentation (= Gebrauchsanweisung = Bedienungsanleitung) und Support
--
Forum cooler nutzen: Hervorhebungen machen und Screenshots posten
--
Es wurde schon alles gefragt, nur noch nicht von allen. (frei nach Karl Valentin)