Aufgrund derzeit hohem Spamaufkommens werden neue Nutzer sehr restriktiv behandelt. Nach kurzer "Bewährungszeit" hat man als normaler Nutzer weitreichende Rechte und benötigt auch kein Captcha mehr.
.
Nutzer, die sich danach dennoch als Spammer oder Trolle erweisen, können jederzeit wieder auf diesen Status zurückgesetzt oder gebannt werden.
Dasselbe gilt für Versuche, politische Überzeugungen kund zu tun, egal aus welcher Richtung diese kommen.
.
.:!: Achtung! Derzeit ist Robonect (noch) nicht mit dem Automower 305 ab Baujahr 2020 zusammen mit der neuen Mäher-FW MSW 41.4.0 kompatibel!
Aber: Im DailyBuild ist ein Patch enthalten, der getestet werden kann! (Stand 15.02.2024)
.
.Du hast Deinen Gardena-Mäher auf die Gardena-Firmware von 2023 aktualisiert?
.:arrow: Testmöglichkeit für das Daily Build.

Das FW-Update am Mäher wird dennoch nicht empfohlen, da das Daily Build nach aktuellen Berichten von Beta-Testern noch keine vollständige Kompatibilität gewährleisten kann! (Stand: 15.02.2024)
Wir empfehlen, das Gardena-Update noch nicht durchzuführen!

.
.

BMS in Husqvarna batteries

Nutze einen Akku mit größerer Kapazität um eines der beiden Ziele zu erreichen.
bortek
Forum-Nutzer
Beiträge: 39
Registriert: Mi 18. Jul 2018, 19:30
Mäher: Husqvarna Automower 420
Firmware des Mähers (MSW): MSW 7.xx.xx
Herstellungsjahr: 2017
Robonect-Modul: Robonect Hx (Rev.5)
Robonect Firmware: 1.0
wurde gedankt: 1 Mal

BMS in Husqvarna batteries

Beitrag von bortek »

Hi

Has anyone opened husqvarna batteries or know if tge contain any discharge protection circuit(like Bms module) in the battery pack?

Or is this implemented in the motherboard of the robot?

The battery looks like this

https://www.kjell.com/se/produkter/el-v ... vyEALw_wcB

Benutzeravatar
insedere
erfahrener Forum-Nutzer
Beiträge: 59
Registriert: Mi 1. Mai 2019, 13:49
Wohnort: Hüllhorst
Mäher: Husqvarna Automower 330X
Firmware des Mähers (MSW): MSW 5.xx.xx
Herstellungsjahr: 2015
Robonect-Modul: Robonect Hx (Rev.5)
Robonect Firmware: V1.0 Beta 7a
wurde gedankt: 1 Mal
Kontaktdaten:

Re: BMS in Husqvarna batteries

Beitrag von insedere »

On the other side of your picture is the balancer under the plastic
LGE
2015er 330x mit robonect hx

bortek
Forum-Nutzer
Beiträge: 39
Registriert: Mi 18. Jul 2018, 19:30
Mäher: Husqvarna Automower 420
Firmware des Mähers (MSW): MSW 7.xx.xx
Herstellungsjahr: 2017
Robonect-Modul: Robonect Hx (Rev.5)
Robonect Firmware: 1.0
wurde gedankt: 1 Mal

Re: BMS in Husqvarna batteries

Beitrag von bortek »

That means the battery itself is protected from total discharge in case if I want to power a Raspberry Pi (with DC/DC converter of course) to batteries plus/minus rails?

RNBO
Forum-Nutzer
Beiträge: 16
Registriert: Di 10. Mai 2016, 12:28
Mäher: Gardena R40Li
Firmware des Mähers (MSW): MSW 6.xx.xx
Herstellungsjahr: 2016
Robonect-Modul: Robonect Hx (Rev.2)
Robonect Firmware: V1.0 Beta 7a

Re: BMS in Husqvarna batteries

Beitrag von RNBO »

I wonder the same = akku BMS for R40/R70 ... akkus.
Where is it possible to get it? Is it just "standard"BMS, ...
Any info is more than welcome.

I've done some more research, and from photos, it looks like akku for R40/R70 do not have BMS (and anyothe charhing logic?) anymore at all.
Can someone (@LitlleJohn ?) confirm this (that BMS is not needed)?

If I understand the ERFAdoc from @Fidatex then the charging logic is inside the roboter, and no additional logic is needed at the akku itself. Ok, BMS makes the life of akku longer.
Gardena R40li

bortek
Forum-Nutzer
Beiträge: 39
Registriert: Mi 18. Jul 2018, 19:30
Mäher: Husqvarna Automower 420
Firmware des Mähers (MSW): MSW 7.xx.xx
Herstellungsjahr: 2017
Robonect-Modul: Robonect Hx (Rev.5)
Robonect Firmware: 1.0
wurde gedankt: 1 Mal

Re: BMS in Husqvarna batteries

Beitrag von bortek »

I disassembled the battery and here are the pics of charging module that sits inside. There is a temp sensor between the backside of the board and batteries. Pics are high res and one can read which IC are used and therefore deduce if whats on the board.

Any thought an what it is are welcome.
IMG_20200711_130834.jpg
IMG_20200711_131207.jpg
IMG_20200711_131405.jpg
IMG_20200711_131502.jpg

RNBO
Forum-Nutzer
Beiträge: 16
Registriert: Di 10. Mai 2016, 12:28
Mäher: Gardena R40Li
Firmware des Mähers (MSW): MSW 6.xx.xx
Herstellungsjahr: 2016
Robonect-Modul: Robonect Hx (Rev.2)
Robonect Firmware: V1.0 Beta 7a

Re: BMS in Husqvarna batteries

Beitrag von RNBO »

From the phot looks like have the same PCB.
It contains BMS,, and charging logic(?).
As charging logic is already part of R40/70, and BMS is not so important you can get accus w/ this PCB.
Gardena R40li

bortek
Forum-Nutzer
Beiträge: 39
Registriert: Mi 18. Jul 2018, 19:30
Mäher: Husqvarna Automower 420
Firmware des Mähers (MSW): MSW 7.xx.xx
Herstellungsjahr: 2017
Robonect-Modul: Robonect Hx (Rev.5)
Robonect Firmware: 1.0
wurde gedankt: 1 Mal

Re: BMS in Husqvarna batteries

Beitrag von bortek »

I should have mentioned that photos of the battery are actually of the original Husqvarna 3200mah battery.

ThomasR
Forum-Nutzer
Beiträge: 47
Registriert: So 19. Jul 2020, 11:53
Wohnort: Nideggen
Mäher: Husqvarna Automower 310
Firmware des Mähers (MSW): MSW 7.xx.xx
Herstellungsjahr: 2016
Robonect-Modul: Robonect Hx (Rev.6)
Robonect Firmware: 1.3

Re: BMS in Husqvarna batteries

Beitrag von ThomasR »

The most important info is missing in the pics. You may actually use any BMS system you like with the Husquarna (at least with my 310 MY2016) as long as the complete battery pack (cells plus BMS) will identify itself properly to the controller. They seem to use a dedicated resistor, that is in one of the (yellow) control wires. In my 310 this is a 3,9k resistor to ground/minus.

A 3rd party battery pack from the bay area did not work because this resistor was missing AND they used the wrong thermistor value. The original thermistor is a 10k type, they had a 20k installed.

With these corrections made the 3rd party battery pack now works perfectly.

I wonder what the resistor value is for: will different resistor values make the controller change anything? Is there anybody OUT there with a larger (original!!) battery pack who may want to identify the value of the resistor used in his pack? I remember reading about larger packs in a 330??

If a modified/enlarged battery pack can properly tell the controller its real size by using the correct identifier resistor, all the circumvents like changing the run time limitation may be unnecessary or the 4h charging time limit is increased?

One more thing about BMS: any LiIon battery pack requires a BMS to protect against overcharge, undervoltage and overtemperature. BUT these BMS are usually made with maximization of availabe energy in mind. They allow charging up to 4,25Volt/cell and discharge to 3 (or sometimes even 2,8) Volts/cell (100% DOD). Under these circumstances any LiIon cell will only last some 500 cycles. To lengthen this lifetime, Husquarna takes control and limits the charging voltage to some 4 Volts and the discharge voltage to some 3,5Volts. This reduces the available capacity up to 50% but tenfolds the lifespan of the battery pack.

ThomasR
Forum-Nutzer
Beiträge: 47
Registriert: So 19. Jul 2020, 11:53
Wohnort: Nideggen
Mäher: Husqvarna Automower 310
Firmware des Mähers (MSW): MSW 7.xx.xx
Herstellungsjahr: 2016
Robonect-Modul: Robonect Hx (Rev.6)
Robonect Firmware: 1.3

Re: BMS in Husqvarna batteries

Beitrag von ThomasR »

Husky.jpg
Original Akku
Husky2.jpg
Nachbauakku (nach der Anpassung, der NTC hängt noch in der Luft)

ThomasR
Forum-Nutzer
Beiträge: 47
Registriert: So 19. Jul 2020, 11:53
Wohnort: Nideggen
Mäher: Husqvarna Automower 310
Firmware des Mähers (MSW): MSW 7.xx.xx
Herstellungsjahr: 2016
Robonect-Modul: Robonect Hx (Rev.6)
Robonect Firmware: 1.3

Re: BMS in Husqvarna batteries

Beitrag von ThomasR »

Groesserer Akku.jpg
Der sollte wohl reichen ;)

War für ein anderes Projekt (10p10s). Ich baue diese Packs aus alten Laptop Akkus selbst :P

Antworten

Zurück zu „Mähzeit oder Lebensdauer des Akku erhöhen“