What to config?

Nutze einen Akku mit größerer Kapazität um eines der beiden Ziele zu erreichen.
Antworten
bortek
Beiträge: 37
Registriert: Mi 18. Jul 2018, 19:30
Mäher: Husqvarna Automower 420
Firmware des Mähers (MSW): MSW 7.xx.xx
Herstellungsjahr: 2017
Robonect-Modul: Robonect Hx (Rev.5)
Robonect Firmware: 1.0

What to config?

Beitrag von bortek »

Hello!

I have just upgraded to new battery with 5200mah instead of the original one with 3200mah.

In the settings in the battery it still shows capacity 2600mah (~80% of total 3200).

How do I change 2600 to higher value so that it mowes longer? Is it possible at all?

ThomasR
Beiträge: 18
Registriert: So 19. Jul 2020, 11:53
Wohnort: Nideggen
Mäher: Husqvarna Automower 310
Firmware des Mähers (MSW): MSW 7.xx.xx
Herstellungsjahr: 2016
Robonect-Modul: Robonect Hx (Rev.6)
Robonect Firmware: 1.2

Re: What to config?

Beitrag von ThomasR »

Hello bortek,

this subject has been discussed in length here but in German only. From what I understand (I‘m relatively new to Robonect)one needs to fool the original Firmware by telling the mower to act like on a secondary mowing area. Supposedly the FW then allows to enlarge the calculated mowing times (calculated from the nominal battery capacity (resistor!!) and minimum voltage required for safe return). If you switch the feature on, the mower will accept almost any battery capacity and run time regardless of the nominal value.

Does this help?

Benutzeravatar
shadowkiller
Beiträge: 2704
Registriert: Do 11. Jan 2018, 08:42
Wohnort: Würzburg
Mäher: Husqvarna Automower 315
Firmware des Mähers (MSW): MSW 10.xx.xx
Herstellungsjahr: 2017 (Modell 2018)
Robonect-Modul: Robonect Hx (Rev.5)
Robonect Firmware: 1.2 (Final Release), WLAN 1.7.3

Re: What to config?

Beitrag von shadowkiller »

Only one additional issue: the statistics for mowing and searching times will no longer be shown in Robonect using this feature. Reason: the mowers electronic ist not saving them using this feature, as result of this Robonect can’t show the mowers statistics.

But if you need to use a bigger battery, this will give you more profit then statistics of it.

In a future version of Robonects Firmware new statistics saved by Robonect will solve this.
WLAN oder Robonect funktioniert nicht? Problemlösungen, Empfehlungen und Tipps
--
Forum richtig nutzen: Hervorhebungen machen und Screenshots posten
--
Kompendium für Mähroboter: Download ERFAdoc (ca. 4,3 MB, 232-Seiten-PDF) von Fidatex
--
Es ist schon alles gesagt, nur noch nicht von allen. (Karl Valentin)

bortek
Beiträge: 37
Registriert: Mi 18. Jul 2018, 19:30
Mäher: Husqvarna Automower 420
Firmware des Mähers (MSW): MSW 7.xx.xx
Herstellungsjahr: 2017
Robonect-Modul: Robonect Hx (Rev.5)
Robonect Firmware: 1.0

Re: What to config?

Beitrag von bortek »

Thanks for the replies. Yes indeed that's the case. I have tested it by switching the extend mowi g time using mowing time adjustment. Moreover the timer function for some reason was not working, maybe due to other issue I found, so the mower was mowing 24/7.

Antworten

Zurück zu „Mähzeit oder Lebensdauer des Akku erhöhen“